+27 73 502 9614 [email protected] Mon-Sat 8:00-17:30
Comprehensive Guide To Choosing The Right Plc

Comprehensive Guide To Choosing The Right Plc

Browse technical resources about solar mounting systems, tracker technology, structural design, and installation best practices.

  • Selection Guide for Low-Loss Active Optical Devices for Photovoltaic Power Plants

    Selection Guide for Low-Loss Active Optical Devices for Photovoltaic Power Plants

    Future PVLPCs must exhibit higher efficiencies and delivered power, robustness at rough environmental conditions, and lower manufacturing cost. This review aims at showing the routes to achieve these goals.


  • The downstream component of an optical module is a memory chip right

    The downstream component of an optical module is a memory chip right

    The flash memory board is a small board typically attached to either the module or the flex cable connecting the DMD and DLP controller. DLP image processing settings specific to the optical module are stored in the flash memory and are used by the DLP controller during. TOSA is the component within the transceiver that is responsible for converting the electrical signal into an optical signal and then transmitting it over the connected optical fiber strand. It consists of a light source (laser diode or light-emitting diode), a monitoring photodiode, and an optical. The optical module serves as a crucial component in optical fiber communication systems, operating at the physical layer, which is the lowest layer in the OSI model. This article will introduce you to the internal components and structure of the optical module.

    [PDF Version]
  • Make several right angles in the cable tray

    Make several right angles in the cable tray

    You can buy a manufactured 90 degree bend or make one on a cable tray bending machine but in this video I show you how to make one using a metal bar. Also, is it possible to place a new cable trays inverted in such a way that the bottom of the cable tray is upside? I welcome any ideas or suggestions. Elbow joint RVS is pushed inside the cable tray and attached with the included screw set. Elbow joint RVS can be used to change a cable tray's horizontal orientation with a range of -90° – +90°. Need more information?The point A is the first angle. I don't know if that will change the math much? I was hoping for something simple like the rise over run thing. Something that I could do on site quickly. The range for adjustable corner piece SRS is 0-75°. Do you want a hard 90 or 2 spaced out 45° bends? Need dimension of tray first width x side wall. Oglaend System manufacture and deliver Multidiscipline modular bolted support systems, cable trays, cable ladders and accessories for complete installation and containment of Instrument, Electrical, Telecom, HVAC and Piping.

    [PDF Version]
  • How to Choose the Right Network Cabinet

    How to Choose the Right Network Cabinet

    The right Network Cabinet size is determined by three key factors: total rack units (U) required, equipment depth, and future expansion capacity. In most business environments, choosing a cabinet with at least 20–30% extra rack space prevents overcrowding and extends system. Selecting the right network cabinet is crucial for the safety and longevity of your network equipment. Moreover, it affects everything from how cool your equipment stays to how much money you spend on power bills each year. Therefore, understanding what makes a good network cabinet. In general, smaller or wall-mount racks are suitable for home or office rack installation; while 4-post racks or enclosed server racks are greater for data centers or server rooms.

    [PDF Version]
  • PLC splitter temperature failure

    PLC splitter temperature failure

    This work presents an experimental and numerical study of the failure behavior of planar lightwave circuit (PLC) optical splitters under uniaxial tensile loading. Based on the experimental results, the specific fr.


  • Airport-grade OSFP optical module 10G selection guide

    Airport-grade OSFP optical module 10G selection guide

    In this article, ETU-LINK will deeply analyze the differences between different 10G SFP+ dual-fiber optical modules from multiple dimensions such as technical parameters, transmission distance, optical fiber type, typical applications, etc., and guide you to make the optimal. Single-fiber bidirectional (BIDI) optical modules must be used in pairs. For example, SFP-10G-BXD1 must be used with SFP-10G-BXU1. If the SFP-10G-ER-1310 is connected. The 10G SFP+ module is the standard transceiver form factor for 10 Gigabit Ethernet (10GbE) links in modern data centers and enterprise networks. Designed as a compact, hot-pluggable interface, it allows switches, routers, and servers to flexibly support high-speed connections over optical fiber or. We provide an industrial-grade reference framework, complying with the latest MSA (Multi-Source Agreement) updates, including SFF-8679 Rev 1. 4 (Jan 2025), to help you design robust, scalable optical fabrics. The Master Reference Matrix: SFP vs.

    [PDF Version]
  • Column-mounted electrical distribution box size guide

    Column-mounted electrical distribution box size guide

    This report provides a comprehensive analysis of electrical distribution board (DB) box sizes, including physical dimensions, electrical capacities, and market trends based on current 2025-2026 standards. The box dimensions shown are inside dimensions. The EZ Box and EZ Trim are provided standard for Pow-R-Line 1X and Pow-R-Line 2X lighting panelboards, as well as Pow-R-Line 3X. This guide explains typical wall-mount and floor-standing dimensions, how to read catalog sizes, and how to choose the right enclosure size for your layout. In practice, “standard sizes” usually means the common size families. Clear detailed description of each size and easy to select with the ordering codes. Box with four studs and adjustable nuts for easy fit / easy remove of pan assembly. Easy fit of incomer devices, aluminum profile with plastic clip for self aligning feature of outgoing MCBs. Larger enclosures may be needed for outdoor use, better protection, or cooling components like fans or vents.

    [PDF Version]

Need Product Pricing?

Contact us for competitive quotes on any of our fiber optic products

Get a Quote